Search bioRxiv⌕ Search
Home/Archive/bioRxiv

bioRxiv · 10.1101/2025.06.09.658654

Fiber-based hydrogels for designing viscoelastic responses in particle-based biomaterials that support embedded 3D printing

Grewal, M. G.·Porter, L.·Helein, G.·Highley, C. B.
View original source ↗Export metadata ↓

Abstract

Viscoelastic biomaterials that exhibit biomimetic responses to applied stresses are important in studying physiology and designing biomaterial scaffolds. Particle-based hydrogels offer potential for engineering viscoelasticity through design of both the component microparticles and their processing into bulk particle-based materials. When particles are not crosslinked to one another, particle movements in response to strain can potentially relieve applied stresses and facilitate the materials use in dynamic processes like bioprinting. In particle-based hydrogels based on spherical hydrogel microparticles (HMPs), particle movement is restricted by contacts with immediately adjacent HMPs. In comparison, fiber-based hydrogel systems leverage high-aspect ratio microfiber components with long-range interactions. Here, microfibers with aspect ratios of [~]15:1 length:diameter are used to form particle-based hydrogels to compare how interparticle interactions at increased length scales alter properties compared to particle-based hydrogels based on spherical HMPs. Like particle-based hydrogels formed from spherical HMPs, those formed from fiber HMPs exhibit viscoelasticity, with shear-thinning and self-healing behaviors. But, fiber-based materials allow enhanced control over bulk stress relaxation times (T1/2 [~] 1-100+ s) across a range of applied strains ({sigma} [~] 2.5-50%) in a packing density-dependent fashion. Fiber-based systems relaxed stresses continually and to a greater degree at low strains in comparison to HMP systems. Dynamic interfiber interactions in fiber-based hydrogels also supported embedded printing where perfusable channels can be printed into fiber-based hydrogels stabilized by physical interfiber interactions. Taken together, fiber-based hydrogels offer opportunities for designing complexity into biomaterial scaffolds, including allowing control over viscoelastic properties through hydrogel design and control over heterogeneous 3D structures through embedded printing.

Source connections

Explore related subjects

bioengineeringPreprint

Keep this discovery

Explore connections, maps & timelines

BibTeXRIS

Grewal, M. G., Porter, L., Helein, G., Highley, C. B.. 2025-06-12. Fiber-based hydrogels for designing viscoelastic responses in particle-based biomaterials that support embedded 3D printing. https://doi.org/10.1101/2025.06.09.658654

Cite the original work for its findings. Save a collection to share your selection of sources.

KEEP EXPLORING

Related preprints

bioRxiv2026

Comparative study of chlorophyll measurement in Physcomitrium patens moss using a conventional microscope adapted for combined 2D+1D imaging and spectral analysis

Imaging spectroscopy often requires expensive and complex equipment. Here we show a simple procedure for attaching a standard miniature fiber spectrometer to a conventional microscope, allowing easy integration of 2D imaging with 1D high-resolution spectral measurements. This combination provides much of the benefit of a full imaging spectrometer without the large equipment investment, and we provide instructions for modifying microscopes to this setup and the present measurements of living cells that demonstrate their performance. Using this setup, we compare the quantitative measurement of chlorophyll concentration in Physcomitrium patens moss using color imaging and spectral sampling.

bioengineering↗
bioRxiv2026

De novo designed single-domain antibodies protect against lethal cobra venom neurotoxicity in vivo

Generative protein design can now rapidly produce de novo binders with high affinity and functional activity against a wide range of targets, including lethal snake venom toxins. However, so far most reported successes rely on new-to-nature scaffolds with limited therapeutic precedent. Single-domain antibodies (VHHs) offer a clinically validated alternative scaffold that can bind and neutralize long-chain -neurotoxins, which are some of the most lethal components in snake venoms. Here we compare three recently established de novo design models with VHH-design capabilities (Germinal, RFantibody, and BoltzGen) for their ability to generate VHHs against the neurotoxin -cobratoxin from the monocled cobra (Naja kaouthia). Using standardized model inputs and evaluation criteria based on AlphaFold3 interface confidence (ipTM) and RMSD self-consistency, we find that Germinal was the only method to generate designs passing stringent in silico criteria for experimental testing. We therefore performed a larger Germinal design campaign employing three different VHH frameworks and experimentally validated 46 designs in vitro. Of these, 42 expressed as soluble proteins and we identified four binding hits derived from two of the three tested frameworks. Of the four binders, two lead candidates were further characterized and demonstrated high affinity (KDs of 4.1 nM and 10.8 nM), monomeric behavior and low polyreactivity, indicating favorable biophysical and developability properties, as well as functional toxin neutralization in vitro. To assess their therapeutic potential we investigated their ability to protect against -cobratoxin toxicity in vivo. Both candidates fully protected mice after -cobratoxin challenge, with 100% survival compared to a lethal control. One candidate also retained notable neutralization capacity against whole venom of Naja kaouthia with a survival of 56%, while the other protected 22% when tested in a rescue setting. Together, we demonstrate that de novo VHH design can generate high affinity single-domain antibodies with in vivo protection against lethal cobra venom neurotoxicity, and provide practical insights into method- and framework-dependent performance.

bioengineering↗
bioRxiv2026

Simple Feedback for Complex Movement: Capturing Whole-Limb Reorganization during Single-IMU Gait Retraining

Clinical gait retraining typically relies on multi-sensor arrays and high-dimensional feedback displays, imposing setup and interpretation burdens that limit routine clinical deployment. We developed a single-IMU visual biofeedback system that delivers real-time feedback of Lower Limb Trajectory Error (LLTE), a composite kinematic error metric integrating knee position and shank angle across the stance phase. Twenty able-bodied adults walked on a treadmill under two visual biofeedback targets (flexed-knee, extended-knee) while receiving either corrected (n=10) or uncorrected (n=8) feedback, where the correction accounted for limb orientation at initial contact. LLTE and stance-phase knee kinematics adapted consistently under the flexed-knee target for both feedback groups, with feedback formulation moderating the temporal trajectory of change. Adaptation toward the extended-knee target was limited, likely because participants were already operating near terminal knee extension and because the scalar error metric provided limited directional information for correction. Ankle range of motion (ROM) changed significantly across the stance phase under both target conditions, while hip ROM did not. Multiscale multivariate sample entropy (MSMVSE) increased monotonically with time scale across all conditions, with no statistically distinguishable difference between corrected and uncorrected feedback. These results suggest that single-IMU LLTE biofeedback can modify gait mechanics and that adaptation was expressed across multiple lower-limb segments rather than through changes at a single joint.

bioengineering↗